Differences

This shows you the differences between two versions of the page.

--- under_monitor_displays [2016/12/21 14:41] – [Making it Automatic] walkeradmin
+++ under_monitor_displays [2023/03/09 22:35] (current) – external edit 127.0.0.1
@@ Line 1: / Line 1: @@
 ====== Under Monitor Displays ======
+<color orange>Dec 2016</color>
 \\
-{{:rpi_umd_001b.jpg?650|}}
 \\
 \\
-<color Red>This Project is work in progress</color>
+{{:alan_lcd_parts.2.crop.jpg?500|}}
 \\
 \\
@@ Line 10: / Line 10: @@
 \\
 \\
-While these can be purchased, they can run in to sever thousand £ for each unit. We only require a simple low cost solution, for this we are using LCD displays that we already own (2 x 40 Char displays from RX units that we are scrapping). These displays will be driven from Raspberry Pis, then input for the diplay messages will be via a web interface to the primary Raspberry Pi.
+While these can be purchased, they can run in to sever thousand £ for each unit. We only require a simple low cost solution, for this we are using LCD displays that we already own (2 x 40 Char displays from RX units that we are scrapping). These displays will be driven from Raspberry Pis, then input for the display messages will be via a web interface to the primary Raspberry Pi.
 \\
 \\
@@ Line 16: / Line 16: @@
 \\
 \\
-{{:8monitorumd.jpg?900|}}
+{{:8monitorumd.jpg?600|}}
 \\
 \\
@@ Line 22: / Line 22: @@
 \\
 \\
-===== Master Raspberry Pi =====
+  * [[What this Project Requires]]\\
-\\
+  * [[Circuit Diagrams and PCBs]]\\
-The primary Raspberry Pi does a little more than the others. As well as writing to the LCD display, this unit has a web server (Apache) and PHP running. The web server hosts a text file (my_data.txt) that is hosted and is editable via a web interface and PHP.
+  * [[Setting up the Master UMD]]\\
-\\
+  * [[Setting up the Slave UMDs]]\\
-For this to work we need the following installed and configured
+  * [[The Python Code]]\\
-\\
+  * [[Code Files]]\\
-\\
-----
-==== Set Static IP Address ====
+  * [[A Massive Gotchya]]\\
 \\
-To set a static IP address, we need to login to the RPi via SSH and change the following file:
-\\
-\\
-The default login is <color red>username: pi and password: raspberry</color>
-\\
-\\
-    /etc/dhcpcd.conf
-\\
-Enter the following
-\\
-    sudo nano /etc/dhcpdc.conf
-    Add these lines to the end of the file (default is dhcp) using  your own IP Address details
-    eth0
-    static ip_address=192.168.1.11/24
-    static routers=192.168.1.1
-    static domain_name_servers=192.168.1.4
-\\
-Use Ctrl-X to exit and Y to save, now reboot the pi and connect to the new address
-\\
-\\
-----
-==== Raspi Config  ====
-\\
-From the terminal, run:
-\\
-    sudo raspi-config
-\\
-You will see the following menu, there are several items we want to change here.
-\\
-\\
-<file>
-┌────────────────────┤ Raspberry Pi Software Configuration Tool (raspi-config) ├───────────────────────────┐
-│                                                                                                          │
-│     1 Expand Filesystem            Ensures that all of the SD card storage is available to the           │
-│     2 Change User Password         Change password for the default user pi)                              │
-│     3 Boot Options                 Choose whether to boot into a desktop environment or the command line │
-│     4 Wait for Network at Boot     Choose whether to wait for network connection during boot             │
-│     5 Internationalisation Options Set up language and regional settings to match your location          │
-│     6 Enable Camera                Enable this Pi to work with the Raspberry Pi Camera                   │
-│     7 Add to Rastrack              Add this Pi to the online Raspberry Pi Map (Rastrack)                 │
-│     8 Overclock                    Configure overclocking for your Pi                                    │
-│     9 Advanced Options             Configure advanced settings                                           │
-│     0 About raspi-config           Information about this configuration tool                             │
-│                                                                                                          │
-│                                                                                                          │
-│                             <Select>                                   <Finish>                          │
-│                                                                                                          │
-└──────────────────────────────────────────────────────────────────────────────────────────────────────────┘
-</file>
-\\
-Select Option 2 (Change User Password) - Change the password to <color red>Ericss0n</color>
-\\
-Select Option 3 (Boot Options) - Change to <color red>B2 Console Autologin Text console, automatically logged in as 'pi' user</color>
-\\
-Select Option 9 (Advanced) then A2 (HostNane) - Change the Hostname to <color red>UMD00n</color> (where n is the display number)
-\\
-Select <color red>Finish</color> when asked to reboot select <color red>Yes</color>
-\\
-\\
-----
-==== Update RPI ====
-\\
-Even if you downloaded the latest version of Raspbian, chances are there are some updates. To update the RPi use the following command line:
-\\
-    sudo apt-get update && sudo apt-get upgrade -y
-\\
-This will most likely take a few minutes on a new install.
-\\
-\\
-----
-==== Install PHP ====
-\\
-We need to install PHP so that the web interface will function. To install PHP use the following command line:
-\\
-    sudo apt-get install php5
-\\
-There is no PHP7 for RPi yet, but version 5 will be fine.
-\\
-\\
-----
-==== Install Apache Webserver ====
-\\
-Apache is the Web Server that will host our website.
-\\
-    sudo apt-get install apache2
-\\
-This may already exist, if so this will also update it.
-\\
-\\
-----
-==== Configure Apache Webserver ====
-\\
-We have to configure Apache Webserver, mainly so that Apache knows where our site is located. There are two files we need to edit, and they are:
-\\
-  * /etc/apache2/apache2.conf
-  * /etc/apache2/sites-enabled/000-default.conf
-\\
-Before we begin this process, create a folder in your home location called Python and give Apache rights:
-\\
-    mkdir /home/pi/Python
-    sudo chmown www-data /home/pi/Python
-    sudo chmod 777 /home/pi/Python
-\\
-We need to copy the website to the /home/pi/Python location, for the Mater there are five files:
-\\
-  * bootstrap.min.css  -  This is a style sheet that controls the look of the site
-  * index.php          -  The main site for entering text (this is what Apache will host)
-  * launchUMD.sh       -  A script to auto start the UMD at boot
-  * my_data.txt        -  This holds the LCD data text, and is edited by the index.php
-  * UMDisplay01.py     -  The Python code that runs the LCD
-\\
-These files need to be copied to the /home/pi/Python location
-\\
-\\
-==== Apache2.conf ====
-\\
-Open and edit the /etc/apache2/apache2.conf file and add these lines:
-\\
-<file>
-<Directory /home/pi/Python>
-        Options Indexes FollowSymLinks
-        AllowOverride All
-        Require all granted
-</Directory>
-</file>
-\\
-Save the file and exit.
-\\
-\\
-==== 000-default.conf ====
-\\
-Open /etc/apache2/sites-enabled/000-default.conf, locate the following lines and edit as follows
-\\
-<file>
-        ServerAdmin webmaster@localhost
-        DocumentRoot /home/pi/Python
-        DirectoryIndex index.php
-</file>
-\\
-\\
-Now reboot the RPi
-\\
-    sudo reboot
-\\
-\\
-----
-==== Edit index.php ====
-\\
-We need to change one line in the index.php, this is the IP Address. This address is the current IP your eth0 has (or the website will not format correctly).
-\\
-    sudo nano /home/pi/Python/index.php
-    look for these lines
-    <link rel="stylesheet" type="text/css"
-            href="http://ipaddress/bootstrap.min.css">
-    <meta name="viewport" content="width=device-width, initial-scale=1">
-    Add your master PI IP address where is states ipaddress
-\\
-Save and close this file.
-\\
-\\
-----
-==== Give Execute Permissions ====
-\\
-There are two files that will be executed by the Pi, these are:
-\\
-  * launchUMD.sh - Autorun at boot, this file launches the UMDisplay01.py
-  * UMDisplay01.py - Runs the LCD
-\\
-To make these files executable run the following from the command line:
-\\
-    sudo chmod 777 /home/pi/Python/launchUMD.sh
-    sudo chmod 777 /home/pi/Python/UMDisplay01.py
-\\
-We should be in a position to test the Pi out now.
-\\
-\\
-----
-==== Test Web Server ====
-\\
-To test the webserver, navigate to your RPi from another computer on the same network, you should see your webpage.
-\\
-http://youripaddress/index.php
-\\
-{{:rpi_umd_004.jpg?300|}}
-\\
-If all is well, you should see a website that looks a bit like the one above. Remember that the text comes from the file <color red>/home/pi/Python/my_data.txt</color> so you can check that file if you are unsure.
-\\
-\\
-----
-==== Test LCD Code ====
-\\
-Assuming that you have connected the LCD to the RPi (via the ribbon cable and driver board) then you can test the code that runs the LCD, on the master this file is the:
-\\
-    UMDisplay01.py
-\\
-This is a python script, you can run this script by entering at the command line:
-\\
-    ./UMDisplay01.py
-\\
-If you are lucky, you will see some text on the LCD, chances are however you will not. This is due to the Potentiometer settings on the driver board, you will need to change these to set the Backlight and LCD intensity.
-\\
-\\
-{{:rpi_umd_005.jpg?300|}}
-\\
-Adjusting these two potentiometers will allow you to balance the text and backlight intensity to get the brightness level you require.
-\\
-\\
-----
-==== Making it Automatic ====
-\\
-The last part is to automate the process of starting the UMD code. For this we need to add the launcher file to a system file on the RPi.
-\\
-\\
-Edit the file /etc/rc.local to automate this process.
-\\
-    sudo nano /etc/rc.local
-    add this line at the end:
-    sudo ./home/pi/Python/launchUMD.sh
-\\
-\\
-To test this, reboot and the LCD should start up automatically (the LCD won't clear on boot, but wait for the "Waiting for 5 Seconds for Network Start" message).
-\\
-\\
-----
-----
-----
-===== Slave Raspberry Pi(s) =====
-\\
-The slave Raspberry Pi(s) download the latest 'my_data.txt' from the Master Raspberry Pi (once a second) so that each slave knows what to display. The 'my_data.txt' file is downloaded using a wget command.
-\\
-\\
-The 'my_data.txt' file has 8 lines, each line is for a particular display, so for example, line 1 & 2 are for LCD1 and reference monitors 1 and 2. Lines 5 & 6 are for LCD and reference monitors 5 & 6.
-\\
-\\
-    Install Raspbian (noobs or Jessie, doesn't matter)
-    Update pi - sudo apt-get update && sudo apt-get upgrade -y
-    Install xrdp (this so we can access the R-pi using RDP if required)
-    Create Python folder (/home/pi/Python)
-    Copy files to python folder:  (might have to change file/folder permissions to www-data)
-        getData (downloads via wget the_data.txt file)
-        UMDisplay0x.py (the code that writes to the display)
-        my_data.txt (contains the 8 lines for the displays, this will be updated by getData)
-        launchUMD.sh (autorun script)
-    Add line to crontab for autoboot
-    Add Python/logs folder
-\\
-\\
-===== Wiring =====
-\\
-The 2 Line is wired to the Raspberry Pi using the following pin out.
-\\
-\\
-{{:pi_lcd_numbers.jpg?300|}}
-\\
-\\
-<color red>NOTE The Pin out shows Pin 14 of the 40Way Pi header connected, but the diagram does not, this is because Pin 14 is GND, so any ground point can be used.</color>
-\\
-\\
-**For this project I am getting some circuit boards made, with a layout similar to this:**
-\\
-\\
-{{:40x2_lcd_pcb_mk2..jpg?500|}}
-\\
-\\
-This circuit board has a 40 pin header to fit to the Raspberry Pi via a ribbon cable, a 16 pin header to fit to the LCD via a ribbon cable. There are two Variable Resistors to adjust the LCD intensity and back-light. There is a 6 way header to allow the addition of three buttons, these will have the following function:
-\\
-  - Display IP Address
-  - Blank Line 1
-  - Blank Line 2
-As the IP addresses on the Raspberry Pi will be DHCP (so we can access them from the corporate network) we might need to check the IP addresses from time to time, as these units are headless, a button to display the IP Address on the LCD display will be useful.
-\\
-\\
-Buttons 2 and 3 are to blank the lines on the LCD, this is so that when doing a 'show and tell' with customers, we can keep them guessing before revealing the content types on the montiors.
-\\
-\\
-===== LCD PCB =====
-\\
-\\
-Here is the PCB, I had a slight issue with the tracks, and to solve this I had to mount the 16 pin header on the bottom of the PCB (the left and right hand pins of the 16W connector would have to be swapped if you wanted to mount the header on the top of the PCB)
-\\
-{{::lcd_pcb_top.jpg?400|}}
-\\
-{{::lcd_pcb_bottom.jpg?400|}}
-\\
-\\
-There are an extra 6 pins for additional GPIO connectivity (they will all connect to ground via a 10KR resistor if fitted. While there are 8 pins, only the upper 6 are fitted.
-\\
-\\
-{{::lcd_pcb_blank.jpg?300|}}
-\\
-\\
-The initial functionality for these will be for 3 buttons:
-\\
-. Hide Line 1
-. Hide Line 2
-. Show IP
-\\
-\\
-Finished LCD PCB running on a Pi Zero.
-\\
-{{::lcd_pcb_working.jpg?600|}}
 \\
 \\
+{{:rpi_umd_001b.jpg?650|}}