aquila_live_stat_mux
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
aquila_live_stat_mux [2023/11/08 12:03] – walkeradmin | aquila_live_stat_mux [2023/11/08 14:13] (current) – [Using Announcer Address] walkeradmin | ||
---|---|---|---|
Line 12: | Line 12: | ||
\\ | \\ | ||
The Multiplexer installer has also changed to allow the specification of stat mux parameters during the installation phase. | The Multiplexer installer has also changed to allow the specification of stat mux parameters during the installation phase. | ||
+ | \\ | ||
+ | \\ | ||
+ | ---- | ||
+ | ==== Multiplexer Installation ==== | ||
+ | One of the steps, when installing the Multiplexer is to specify what Stat Mux multicast address(s) to use, this is done from the command line when doing the install. | ||
+ | < | ||
+ | ./ | ||
+ | </ | ||
+ | The important part from the stat mux perspective is the announcer address | ||
+ | \\ | ||
+ | \\ | ||
+ | --muxAnnouncer 239.225.0.1 --statmuxAnnouncer 239.225.0.1 --simulcryptAnnouncer 239.225.0.1 --bisscaAnnouncer 239.225.0.1 | ||
+ | \\ | ||
+ | \\ | ||
+ | The address in the above example has been used for all announcers, each announcer uses a unique port. | ||
+ | \\ | ||
+ | \\ | ||
+ | ---- | ||
+ | ==== Finding Announcer Address ==== | ||
+ | If you performed the installation, | ||
+ | \\ | ||
+ | \\ | ||
+ | We can get this information from the Multiplexer, | ||
+ | k9s | ||
+ | This will launch the k9s application | ||
+ | \\ | ||
+ | \\ | ||
+ | {{ : | ||
+ | \\ | ||
+ | \\ | ||
+ | Scroll down and select the POD ' | ||
+ | \\ | ||
+ | \\ | ||
+ | {{ : | ||
+ | \\ | ||
+ | \\ | ||
+ | Show the contents of the folder using ' | ||
+ | \\ | ||
+ | \\ | ||
+ | To find the announceAddress enter the following | ||
+ | cat smxMasterIni.json |grep announce | ||
+ | You will get an output similar to below: | ||
+ | < | ||
+ | " | ||
+ | " | ||
+ | " | ||
+ | " | ||
+ | " | ||
+ | </ | ||
+ | To get out of the K9s use ' | ||
+ | ---- | ||
+ | ==== Using Announcer Address ==== | ||
+ | \\ | ||
+ | The last big difference in v7 is that now you have to specify the announcer address in your services using and ' | ||
+ | \\ | ||
+ | \\ | ||
+ | When creating the Encoding Live services for your stat mux, you need to add a parameter to the ' | ||
+ | \\ | ||
+ | \\ | ||
+ | {{ : | ||
+ | \\ | ||
+ | The advanced parameter is: | ||
+ | statmux.announce.addr | ||
+ | | ||
+ | statmux.announce.addr | ||
+ | \\ | ||
+ | The above is just an example, you will need to use the multicast address from your system. | ||
\\ | \\ | ||
\\ | \\ | ||
aquila_live_stat_mux.1699445031.txt.gz · Last modified: 2023/11/08 12:03 by walkeradmin