rx1_modulated_input
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
rx1_modulated_input [2023/11/07 15:22] – walkeradmin | rx1_modulated_input [2023/11/07 15:43] (current) – [RX1 Input Status] walkeradmin | ||
---|---|---|---|
Line 12: | Line 12: | ||
\\ | \\ | ||
\\ | \\ | ||
- | {{ : | + | {{ : |
\\ | \\ | ||
The Monitor F-Type output of the AVP is connected directly to the RF input of the RX1 (RX4 is on the left). There is no up-convertor or attenuator in use. | The Monitor F-Type output of the AVP is connected directly to the RF input of the RX1 (RX4 is on the left). There is no up-convertor or attenuator in use. | ||
Line 25: | Line 25: | ||
{{ : | {{ : | ||
\\ | \\ | ||
+ | |||
=== Output Parameters === | === Output Parameters === | ||
+ | < | ||
RF Carrier ID State On (don't confuse this with Modulation on) | RF Carrier ID State On (don't confuse this with Modulation on) | ||
Output Select | Output Select | ||
Output State On Reduced Power (we don't want to overload the RX1 input) | Output State On Reduced Power (we don't want to overload the RX1 input) | ||
Output Power-up State (Last State) | Output Power-up State (Last State) | ||
- | \\ | + | |
- | \\ | + | </ |
=== L-Band Output === | === L-Band Output === | ||
+ | < | ||
Frequency Input Mode | Frequency Input Mode | ||
L-Band Frequency | L-Band Frequency | ||
Line 41: | Line 44: | ||
L-Band Up-converter Frequency | L-Band Up-converter Frequency | ||
Upconverter Power Off | Upconverter Power Off | ||
- | Upconverter Reference | + | Upconverter Reference |
+ | </ | ||
+ | \\ | ||
+ | \\ | ||
+ | The settings on this page determine what frequency you are transmitting on. | ||
+ | \\ | ||
+ | \\ | ||
+ | ---- | ||
+ | ==== AVP Modulation Parameters ==== | ||
+ | Below is the Modulation settings I used on the AVP Modulator. | ||
+ | \\ | ||
+ | \\ | ||
+ | {{ : | ||
+ | \\ | ||
+ | < | ||
+ | Modulation Standard | ||
+ | Modulation State On | ||
+ | Modulation | ||
+ | FEC Rate 3/4 | ||
+ | Frame Size | ||
+ | Pilots | ||
+ | NCR Stamping PID | ||
+ | Symbol Mapping Mode Mean Power | ||
+ | PL Scrambling Sequence Number | ||
+ | Symbol Rate 31.25 | ||
+ | Roll-off Factor | ||
+ | Bandwidth | ||
+ | </ | ||
+ | \\ | ||
+ | The settings on this page determine the amount of bandwidth that is available, in this case it is 37.5 Mhz. | ||
+ | \\ | ||
+ | \\ | ||
+ | ---- | ||
+ | ==== RX1 Input Settings ==== | ||
+ | See Below for the RX1 Demodulation settings. | ||
+ | \\ | ||
+ | \\ | ||
+ | {{ : | ||
+ | \\ | ||
+ | \\ | ||
+ | < | ||
+ | Input Type Satellite | ||
+ | Source | ||
+ | LNB | ||
+ | LNB Frequency | ||
+ | LNB Voltage | ||
+ | 22kHz not selected, same reason as above. | ||
+ | |||
+ | Tuner | ||
+ | Frequency | ||
+ | Symbol Rate 31.25 | ||
+ | Search Range 10000 | ||
+ | C/N margin alarm 2.0 | ||
+ | |||
+ | Everything else off. | ||
+ | </ | ||
+ | \\ | ||
+ | \\ | ||
+ | ==== RX1 Input Status ==== | ||
+ | \\ | ||
+ | On the same page as you entered the RX1 demodulation settings, once you have started the receiver service, you should see the following input status. | ||
+ | \\ | ||
+ | \\ | ||
+ | {{ : | ||
+ | \\ | ||
+ | \\ | ||
rx1_modulated_input.txt · Last modified: 2023/11/07 15:43 by walkeradmin